DIY Kingsize Headboard

What’s this – 2 blog posts in 2 weeks? That’s almost unheard of round here! You would think I have excess time on my hands. Actually, that’s quite far from the case, in fact things are more hectic than ever! I’ve recently taken on a new role at work which I’m delighted about and we’re focusing more and more time on wedding planning! In among all that, we have a house to fill with furniture to make it look less like a shell… Quite a task when you only started with 2 side tables and a temperamental floor lamp! The good news is that things are coming along and this past week we finally managed to MAKE and INSTALL a headboard for our bed!

img_1840

I’d like to just take a minute to talk about the bed. This bed is my most favourite purchase for the house. It is the most comfortable thing I’ve ever had the pleasure of flopping my body onto. You don’t appreciate how important a bed really until you have a crap one. In our old house the bed and mattress were brand new but SO uncomfortable to me. The mattress gave me such a sore back on it’s own that we had to invest in a memory foam topper just so I could get some sleep. When we were choosing our bed I was basically prepared to throw ALL THE MONEY at it because it was so important to me. We tried many, many shops and finally settled on this dream king size divan & mattress set. I won’t mention where it’s from as the service I had from the shop was pretty terrible but even that doesn’t dampen my love for this bed. ANYWAY, when we bought the bed we decided to pass on the headboards they had available in the shop because there was no way I was spending another £250 on a piece of covered MDF – thank you very much! We decided we could at least try to make one for a fraction of that cost and I think it turned out pretty well.

The process was pretty simple and the cost of all the materials (including a swish new staple gun) came to under £90 which I’m delighted with. In true blogger style I attempted to document the process. Also this is the first real DIY project that Ian and I ever ever worked on as a team so I thought adding more stress to the situation by stopping every 5 minutes to take a photo would be a good idea 🙂

Materials

  • MDF board (cut to size at B&Q for free)
  • 2 pre-cut wooden posts (also B&Q)
  • 2m of upholstry fabric (from Remnant Kings)
  • 2m of wadding fabric (Remnant Kings)
  • 2inch thick foam (cut to the correct size and bought at the most random little shop in Glasgow city centre that exclusively sells foam products – who knew?)
  • Staple gun & staples (Amazon)
  • Sandpaper, nails and other handy DIY tools like a drill
*Gathering the materials for this job was the most difficult part. Not because they were hard to come by, but because we were woefully under-prepared for how big a bit of MDF we would need to fit into Ian’s tiny toy car. Basically, the main thing I’m taking away from this project is that we need a bigger car in our arsenal.

Once we actually had all of the above in our possession, we set up a make-shift work bench (*note to self: Get proper work bench for future DIY projects) from lawn furniture in the garage. Then Ian started brandishing tools.

Look at all that brandashing
Look at all that brandishing *Still has the sleeve on – we have no idea what we’re doing.

It may not seem like it, but we know our limitations so went for a very basic square headboard. The MDF is the same width as the bed (152cm) and we figured we would need the height to be 80cm taller than the mattress. We measured the spacing of the holes in the divan meant for the headboard screws and transferred this to the posts, making 2 holes in each one. We then spaced the supporting posts 15cm in from the edge of the MDF and secured them with wood glue and nails for extra stability. This is the basic frame in the crap picture above!

The foam was cut to the same dimensions as the board and is 2 inches deep so it’s nice and cushioned. We attached this with some spray adhesive to the top of the board just to hold it in place for all the yanking that was to come.

img_1837

We laid our wadding out and placed the frame face down on top of it so that the side with the posts was facing up. Taking it in turns (because it was actually hard work) we then pulled the wadding tightly over it to smooth out the edge of the foam and secured it to the back using the staple gun. Once the wadding was secured we repeated this step with the actual fabric.

img_1838

This took a fair amount of time and caused more than a little grunting on my part. We found the best way was to pull tightly on the 3 visible edges and then yank with all our might on the bottom edge so that it compressed the foam to the board. It’s kind of hard to explain but hopefully you can see from the picture below what I mean. This taught edge means that the headboard meets the mattress nice and snug.

img_1843

LOOK HOW DELIGHTED HE IS WITH OUR HANDYWORK!

I paid special attention to the corners and found a way to fold in the fabric so that it was kind of mitred. We cut slits in the wadding and fabric to be able to wrap both around the posts. This but won’t be visible so we weren’t too concerned about how it looked, as long as nothing was poking out! Below you can see how long the posts extend down from the board. We wanted to make the frame as sturdy as possible while making sure it would be flush with the wall. Ideally the posts would go all the way to the floor when the headboard is attached but then they would be hitting the skirting board behind the bed and would angle the board which may cause splintering. (I EVEN SOUND LIKE I KNOW WHAT I’M DOING NOW!)

img_1755

This is the back of the board and one of the corners. It looks pretty crap but it’s very secure and looks lovely from the front which is the main thing. I also turned under the raw edge of the fabric and stapled that to the board too so we wouldn’t have any fraying.

It’s quite the structure once it was attached to the bed, almost imposing, but it definitely completes the room and makes the bed feel even more luxurious! I’m calling our first joint DIY project a success and now I have about 5 bajillion more things that I want to make 🙂 On to the next one!

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s